Overview#

A patch cable, as used here, is a cable that would be used from a PC to the wall or PC to a network Hub or Switch.

Before you begin creating your CAT 5 patch or Network Crossover Cable, it's important to point out that the method outlined here is only one method. It is by no means the only or best method. Also, make sure you have all the necessary tools and materials before you begin. You will need a length of CAT cable, several RJ-45 connectors, and a crimp tool.

  • Most crimp tools have two blades: one designed to cut completely through a cable and the other designed to strip the cable jacket/insulation. Using the latter blade, strip the cable jacket/insulation back about an inch, so all the wires inside are exposed. Be careful not to cut the inside wires when stripping the cable’s insulation.
  • With the jacket/insulation removed, you'll find eight wires and a string inside the CAT 5 cable. Cut the string off, and untwist the wires back to within one-eighth inch of the jacket.
  • Fan the wires out from left to right in the order they are to be crimped. The crimping order depends on the type of cable you are making. For this guide, we will be wiring the cable to CAT 5 EIA 568B specifications. This is the configuration for a standard CAT 5 patch cable (See Table 1 and Figure A).
  • Grasp the wires firmly between your fingers and flatten them to remove their curliness. The wires must lay flat and together, aligned as closely as possible. Try not to get them out of order.
  • While holding them firmly, cut off about a half-inch of the exposed wires, so they are all the same length.
  • Slide the RJ-45 connector onto the wires, making sure the wires stay lined up. The connector has eight slots, one for each wire. Try to make each wire reach the end of its slot. The cable jacket/insulation should reach just beyond the end of the crimp point. If the insulation doesn’t reach far enough inside the connector or if the wires don't reach the end of their slots, cut the wires off a bit more. If the cable jacket/insulation reaches too far past the crimp point, simply trim off a little more jacket/insulation.
  • Next, verify all the wires are in the correct order, and insert the connector into the crimping tool. Crimp it! This requires a little bit of strength, and you may need to use two hands.
  • Now repeat steps 1 through 7 for the opposite end of the patch cable, and you're finished.

Patch Cable/modular_plugs_wiring configuration.pdf(info)#

Patch Cable/modular_plugs_wiring configuration.pdf(info) shows a good layout of Modular Plugs Wiring Configurations

EIA/TIA T568B color code wiring diagram #

Pin #Wire ColorWire Function
1White/OrangeTransmit pair 2
2OrangeReceive pair 2
3White/GreenTransmit pair 3
4BlueReceive pair 1
5White/BlueTransmit pair 1
6GreenReceive pair 3
7White/BrownTransmit pair 4
8BrownReceive pair 4

Network Cables/Standard-EIA-TIA-T568B-Wiring-Diagram.png

Standard EIA/TIA T568A Wiring Diagram#

Pin #Wire ColorWire Function
1White/GreenTransmit pair 3
2GreenReceive pair 3
3White/OrangeTransmit pair 2
4BlueReceive pair 1
5White/BlueTransmit pair 1
6OrangeReceive pair 2
7White/BrownTransmit pair 4
8BrownReceive pair 4

Network Cables/Standard-EIA-TIA-T568A-Wiring-Diagram.png

Note: The first color listed in the color pair is the dominant color of the wire. In other words, White/Orange is a white wire with orange stripes. Some wire manufactures may use slightly different color indicators.

More Information#

There might be more information for this subject on one of the following:

Add new attachment

Only authorized users are allowed to upload new attachments.

List of attachments

Kind Attachment Name Size Version Date Modified Author Change note
pdf
modular_plugs_wiring configura... 22.1 kB 1 04-Aug-2016 16:34 jim Wiring Configurations for Modular Plugs
« This page (revision-6) was last changed on 04-Aug-2016 16:35 by jim